ade-3100 manual

IGMP is available in all modes and all encapsulations. IGMP querier will send IGMP query packet. When a PVC has a token available, it can transmit cells at the rate of PCR. After a cell is transmitted, the PVC loses the token it has accumulated. The Router can support up to total of 16 PPP sessions, and each PVC can support up to 8 PPP sessions. If a different User Note Name with an already existing Account ID is submitted, it will replace the previous account with that Account ID. You can have the same User Name and Password for two different accounts (Account ID). The default is 0, which means never disconnect from the ISP. Range: 0-32767 Default: 0 PPP Idle Timer Config: It will link you to the PPP Disconnect Timer Configuration page (see Section 5.4.3). The NAT module provides Dynamic Network Address and Port Translation (Dynamic NAPT) capability between LAN and multiple WAN connections, and the LAN traffic is routed to appropriate WAN connections based on the destination IP addresses and the Route Table. Default is Enable. Mode: Options for the NAT dropdown menu are: NAT: Static peer-to-peer mode (1x1). NAPT: Static multiple mapping mode (1xN). Dynamic NAPT (default): Dynamic multiple mapping mode (NxN). Session Name: It allows you to select the session from the configured NAT Session Name Configuration.Public Port - Start: It allows you to enter the port number of the Public Network (WAN or external network). If you are entering a range of ports, this is the first port. Public Port - End: It represents the last port number in a port range. See the next page for instructions on how to configure this. The Source MAC must consist of 12 hexadecimal characters. Destination MAC: This is the Destination MAC to block or to forward to. See the next page for instructions on how to configure this. The DNS proxy on the Router records the available DNS servers and forwards DNS query messages to one of DNS servers.

• ade-3100 manual, ade-3100 manual.

This documentation may refer to numerous hardware and software products by their trade names. In most, if not all cases, these designations are claimed as trademarks or registered trademarks by their respective companies. All setup and provisioning is accomplished via a simple intuitive Web interface which further enhances the user experience. 1.1 Features ADSL Compliance Compliant with ADSL standards Full-rate ANSI T1.413 Issue 2 and ITU G.dmt (G.992.1) standards Splitterless ITU G.lite (G.992.2) specification ADSL over POTS (Annex A) and ADSL over ISDN (Annex B) DMT modulation and demodulation. Front panel of ADE-3100 LED Indicators of ADE-3100: LEDs Color. Rear panel of ADE-3100 Rear panel of ADE-4100 RESET button: The Router comes with a reset button built into the rear panel. Use this button to restore the factory default settings. Admin account also has FTP server access.This includes LAN, WAN, DHCP, PPP, and ADSL status. These pages can be viewed and modified by both user and admin accounts. 4.1 Home Page The Home page shows the firmware versions;. This page contains information that is dynamic and will refresh every 8 seconds. PPP interfaces can be created, modified, and deleted in the PPP Configuration page. Refer Note to Section 5.4 for further information. The information displayed on this page is either inherent to the Router or set by the ADSL Central Office (CO) DSLAM, neither of which cannot be changed by the user. The SNR Margin is set by Central Office DSLAM. If the SNR Margin is increased, bit error rate performance will improve, but the data rate will decrease. Conversely, if the SNR Margin is decreased, bit error rate performance will decrease, but the data rate will increase. These pages can be viewed and modified by both user and admin accounts. When any settings are changed, please go to the Save Settings page to save the new Note setting(s) and reboot the Router. For instance, Router mode uses NAT which requires ALG support.

This page contains information that is dynamic and will refresh every 2 seconds. 6.9 Admin Password Configuration The Admin Password Configuration page allows you to set the password for administrator.This page contains information that is dynamic and will refresh every 5 seconds. 6.13 Local Code Image Update The Local Code Image Update page allows you to upgrade the image code locally. Firstly, you need to download the new code to your local drive. Never power off after download start. Note: If system doesn’t get into this page in a long time, please power on again then click Local Code Image Update again. 4. Display “File successfully transferred” message when upgrade successfully. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. User data in the form of Ethernet frames is encapsulated into AAL5-PDU for transport over ATM. RFC-1483 provides no authentication and configuration such as would be provided by PPP.Question 3 Since only one PVC is mapped to one local PC IP address, why can I input more than one IP address for one NAT session. Answer 3 Even it is applicable to insert multiple IPs for NAT mapping, only the first IP address of. All rights reserved. The products and programs described in this User ’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted. Page 3 Trademarks The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous hardware and software products by their trade names. In most, if not all cases, these designations are claimed as trademarks or registered trademarks by their respective companies. Page 4 TABLE OF CONTENTS CHAPTER 1 INTRODUCTION.1 ADE-3100 FEATURES.

You need to apply for a DNS domain name from The Router will update the WAN IP address to DDNS’s database once a WAN port was connected to Internet if Dynamic DNS function is enabled. Regular user account does not have authorization to view or alter the content on the pages in the Admin Privilege section. 6.1 WAN Status The WAN Status page shows the information and status of WAN PVCs. Annex Mode Config: It allows you to manually configure the Router for Annex A or Annex B mode by selecting User Configured and choosing the Annex Mode in the next field. If there is a Gateway associated with the selected Network Interface, then that Gateway’s IP address appears in the Gateway field of the route entry. If the selected Network Interface is dynamic but the connection is not established, then the route entry does not appear in the Routing Table. Have this number lower if you want a more frequent refresh rate. Range: 0 - 32767 Default: 100 6.6 RIP Configuration RIP (Routing Information Protocol) is a management protocol that ensures that all hosts in a particular network share the same information about routing paths. This timer specifies how often the RIP sends announcements as a RIP Supplier. Range: 0 - 2147483647 Default: 30 Expire Timeout:It allows you to enter the Expire Timeout in seconds. This timer specifies the expiration time of a route. HTTP Server Access: It allows you to configure where these Web pages could be accessed from. All (default): When this field is checked, it allows both WAN and LAN access to the Web pages. System default is Enabled. Disable WAN side FTP access: This will disable WAN side access to the FTP server, default is Disabled. TFTP server: It allows you to enable or disable the TFTP connection. System default is Disabled. DMZ: A DMZ (De-Militarized Zone) is added between a protected network and an external network, in order to provide an additional layer of security.

Ensure ADE-3100 is powered OFF. Page 11 ADE-3100 User Manual Connect the supplied power adapter to ADE-3100 and power up. Use only the power adapter provided. Using a different one may cause hardware damage. Step 5 Check the LEDs The LNK LED of LAN should be ON (provided the PC is also ON.). The ADSL LED should be also ON. Page 12 Login And System Status Chapter 3 Login And System Status 3 This Chapter details the first time login procedure and the Status screen Login ADE-3100 contains an HTTP server. This enables you to connect to it, and configure it, using your Web Browser. Your Browser must have JavaScript support. It shows the firmware versions and WAN and LAN interface status. Figure 3-2: Home page ADSL The ADSL Status page shows the ADSL physical layer status. Page 15 ADE-3100 User Manual LAN The LAN page shows the information and status of LAN port, DHCP client table, and linking status of Ethernet interface. Figure 3-4: LAN status PPP The PPP page shows the status of PPP for each PPP interface. For details, see Chapter 5 PC Configuration. WAN configuration Select the WAN link under Configuration column to set up WAN connection. It is required to know the type of Internet connection service used by your ISP. Page 17 ADE-3100 User Manual Figure 4-2: Per VC Settings To switch between the PVCs, please choose the options of virtual circuit and click on the Submit button to switch over. Figure 4-3: Switch between PVCs Internet connection services Types of Internet connection services supported by ADE-3100 are explained below. Enable “Bridge”, and choose suitable packet encapsulation. Page 18 System Configuration Figure 4-5: Encapsulation types of Bridge mode Step 2 Click “submit” to commit modifications you’ve done, then click “Save Configuration” to store settings. (Modifications will not take effects until next reboot.) Step 3 Click on “NAT” tab on left panel, and disable the NAT function in the option menu.

1 Internet Access Features.1 Advanced Functions.1 LAN Features. Page 5 TCP STATUS.38 ROUTE TABLE.39 LEARNED MAC TABLE.40 ADSL CONFIGURATION.41 RIP CONFIGURATION. Page 6 Chapter 1 Introduction 1 This Chapter provides an overview of ADE-3100's features and capabilities. Congratulations on the purchasing of ADE-3100. The ADSL Modem Router will allow multiple LAN users to share an Internet user account, via a DSL connection. Once the ADSL Modem Router is installed and configured, the Internet is just a click away. Page 7 ADE-3100 User Manual LAN Features w DHCP Server support. Dynamic Host Configuration Protocol provides a dynamic IP address to PCs and other devices upon request. ADE-3100 can act as a DHCP Server for devices on your local LAN. Use WEB browser from anywhere to begin the configuration.PLANET ADE-3100 can be managed from any PC on your LAN. And, if the Internet connection exists, it can also (optionally) be configured via the Internet. Page 8 Introduction Physical Details Front Panel PWR ADSL LNK READY TX ACT RX WAN ADSL Modem Router LAN ADE-3100 Figure 1-2: Front Panel LED definitions LEDs Color Active Description PWR Green ON The power adaptor is connected to the Modem. READY Green Blink ADSL Green ON ADSL connection is established. TX Green Blink Transmitting data via ADSL link. RX Orange Blink Receiving data via ADSL link. LNK Green ON ACT Green Blink WAN LAN The system is ready to use. Page 9 ADE-3100 User Manual If ADE-3100's IP Address or password is lost, the following procedure can be used to recover from this situation. Pressing the Reset button for more than 10 seconds. ADE-3100 will restore to factory default setting. Note that this should be done only when you had tried all the troubleshooting options. Pressing the Reset button during operation may bring you into the risk of creating IP address conflict between your PC and the router. Page 10 Chapter 2 Installation 2 This Chapter covers the physical installation of ADE-3100.

NAT Session Name Status displays at the bottom of this page to show all the NAT Session Names with its WAN Interface. Page 31 ADE-3100 User Manual requests of your network, ADE-3100 will forward those requests to the appropriate computer. (Note: DHCP function must be disabled or the local server itself has to be fix-IP addressed to use this function.) This function is generally used to set up a web server, ftp server, or e-mail server on your network. Figure shows the screen of Virtual Server Configuration page, To add a Virtual Server: Step 1 Select the public port number used by the service, ranged from 0 to 65535. Page 32 System Configuration DNS Configuration The DNS Configuration page allows you to set the configuration of DNS proxy. ADE-3100 supports the DNS proxy function. For the DHCP requests from local PCs, the DHCP server will set the LAN port IP as the default DNS server. Thus, all DNS query messages will come into LAN port first. The DNS proxy on the ADSL modem recorded the available DNS servers, and forward DNS query messages to one of DNS server. Page 33 ADE-3100 User Manual packets will be forwarded to the destination PC. Destination MAC When the bridge filtering is enabled, enter the Destination MAC address, select Block and click Add. Then all incoming WAN and LAN Ethernet packets matched with this destination MAC address will be filtered out. If the Forward is selected, then the packets will be forwarded to the destination PC. For example, 0800 is for IP protocol. You should then see a screen like the following. This is the default Windows settings. If the DNS Server Search Order list is empty, enter the DNS address provided by your ISP in the fields beside the Add button, then click Add. You should then see a screen like the following. This is the default Windows settings. Restart your PC to ensure it obtains an IP Address from ADE-3100. Page 39 ADE-3100 User Manual Windows XP 1. Select Control Panel - Network Connection. 2.

Right click the Local Area Connection and choose Properties. You should then see a screen like the following. Page 40 System Configuration Using DHCP To use DHCP, select the radio button Obtain an IP Address automatically. This is the default Windows settings. Restart your PC to ensure it obtains an IP Address from ADE-3100. Page 41 ADE-3100 User Manual Macintosh Clients From your Macintosh, you can access the Internet via ADE-3100. Page 42 Chapter 6 Admin Privilege 6 This Chapter details the operation of ADE-3100 and the status screens. The links under Admin Privilege are only to be accessed and configured, when it is login with administrator login name and password. WAN Status The WAN Status page shows the information and status of WAN PVCs. Select the VC number to view connection status. The DHCP Release and Renew allows users to release and renew the WAN IP address in the WAN DHCP Client Enabled (dynamic) mode. Page 43 ADE-3100 User Manual Figure 6-2: ATM Status Screen TCP Status The TCP Status page shows the statistics for all TCP connections. This is for internal network only. Page 44 Admin Privilege Route Table The Route Table page displays routing table and allows you to manually enter the routing entry. The interface br0 means the USB interface; lo0 means the loop back interface. Page 45 ADE-3100 User Manual System Default Gateway Configuration The system-wide Default Gateway now provides three options: Auto, Userselected Network Interface, and None. None This field allows the user to choose to have no Default Gateway in the CPE Auto This field allows the user to select the CPE to automatically decide the Default Gateway. (System Default) User-selected Network Interface This field allows user to select a Network Interface from a list (PVCs, PPP Sessions, USB and LAN). Page 46 Admin Privilege ADSL Configuration The ADSL Configuration page allows you to set the configuration for ADSL protocols. Trellis Trellis Code. By default, it is always enabled.

Figure 4-6: NAT Disable screen Step 4 Click “Save settings” on left panel to write configuration into machine, and reboot to make settings effective. Page 19 ADE-3100 User Manual be obtained from ISP. Disable “Bridge”. (Packet encapsulation information also has to be obtained from ISP. Page 20 System Configuration connection handshake. The default value is 1432. Authentication When AUTO option is chosen, the PAP mode will run first then CHAP. Automatic Reconnect If you check this option, the Disconnect Timeout should set to 0 second. Otherwise there will be a conflict between them. DHCP Leave this option unchecked. Figure 4-8: PPP setting Screen Step 3 Click on “NAT” tab on left panel, and enable the NAPT function in the option menu. Page 21 ADE-3100 User Manual Fixed IP for WAN If your ISP has assigned static IP address, you may connect to the Internet by using a fixed, or static address. To set up a Fixed IP for WAN, do the following steps as an example. Step 1 Enter the information of Static IP Address, Subnet Mask and Gateway provided by ISP. Note: These parameters are required for building up connection. If one of these information incorrect or unavailable, please contact your ISP for correct information. Page 22 System Configuration Figure 4-10: DHCP client enable Step 3 Click on “NAT” tab on left panel, and enable the NAPT function in the option menu. Step 4 Click “Save settings” on left panel to write configuration into machine, and reboot to make settings effective. Other settings Here are explanations about some fields not mentioned above. MAC Spoofing The MAC Spoofing is developed to solve the scenario when the ISP only recognizes one MAC address. Copy the ISP-recognized MAC address here. Table 4-1 IGMP packets process Note: Before the IGMP mode is enabled; please go to the Misc Configuration page to enable the IGMP proxy. Otherwise, the IGMP selection will not be valid.

Page 24 System Configuration Table 4-2 WAN configurations Overview Bridge Mode (Dynamic IP) Configuration - WAN Enabled. The default IP is 10.0.0.2 for IP and 255.0.0.0 for Subnet Mask. Figure 4-13: LAN Configuration DHCP Setting A DHCP (Dynamic Host Configuration Protocol) Server automatically assigns IP address to each computer on your network. Unless you already have one, it is highly recommended that your router be set up as a DHCP server. You can specify the type of LAN connection or use AutoSense. Default is AutoSense. Figure 4-15: Ethernet Mode PPP Configuration This page allows the user to configure multiple PPP sessions for each PVC. It can support up to total of 16 PPP sessions, and each PVC can support up to 8 PPP sessions. Y PVC This field allows the user to choose the specific PVC for PPP session. Y Service Name The service name of PPP is required by some ISPs. If the ISP does not provide the Service Name, please leave it blank. Page 28 System Configuration PPP Configuration Status will be displayed at the bottom of this page to show all the Session Names with its Adapter (PVC number), Mode (PPPoA or PPPoE), Service Name, Account to Use (PPP Account ID), Disconnect Timeout configuration, MRU, MTU, MSS, Authentication Mode (Auto, CHAP or PAP), and Auto Reconnect configuration. To configure the above settings, you must go to the PPP Account Configuration page first to configure Account ID, Users Name and Password. Page 29 ADE-3100 User Manual more than one local PC can be associated with one WAN Interface. Click the Session Name Configuration link to add the session name for WAN interface. Figure 4-18: NAPT configuration Y Session Name This field allows the user to select the session from the configured NAT Session Name Configuration. Y Interface This field allows the user to choose specific WAN Interface (PVC or PPP Session) for NAT Session.

Handshake Protocol This is for the ADSL handshake protocol. Wiring Selection The wiring selection for the RJ-11. Bit Swapping Bit swapping enables an ADSL system to change the number of bits assigned to a subcarrier, or change the transmit energy of a subcarrier without interrupting data flow. Page 47 ADE-3100 User Manual This field allows the user to Enable or Disable the RIP session. The resulting RIP session will monitor all network interfaces that are currently available for messages from other RIP routers. Supplier Interval This field allows the user to enter the Supplier Interval timer in second. Current RIP Settings displays the each interface’s RIP status. Page 49 ADE-3100 User Manual Figure 6-9: Miscellaneous Configuration Screen WAN side HTTP server When it is enabled, the Web setting pages of ADE-3100 can be accessed from the WAN side. Users can limit the administration privileges to a specified IP address or limit to LAN side user. Page 50 Admin Privilege When it is enabled, the FTP connection can be established from both the LAN and WAN sides. TFTP server When it is enabled, it can upgrade the image code with the TFTP client application run at either the LAN or WAN sides. An example for the TFTP client updating the vxworks.z product image code is: Figure 6-10: Example for TFTP server HTTP server port HTTP server port in ADE-3100 can be changed to other secure port number. Page 51 ADE-3100 User Manual nect: Some ISPs would terminate the PPP session due to the inactivity. For the PPP connect on WAN access, the PPP will be automatically reconnected when an URL is entered in the browser (packet interested in going out the WAN). For the Automatic Reconnect, it will reconnect the PPP session whenever it is terminated by ISP. Page 52 Admin Privilege Code Image Update The Code Image Update page allows you to upgrade the image code locally. Browse the location of firmware file, and click the Upload to start the update.

Network Code Image Update The Network Code Image Update page allows user to upgrade the image code from remote FTP server. Assume an FTP server stores the updated image on Internet. Click Image Download to initiate the updating. Page 53 Appendix A Troubleshooting A This Appendix covers the most likely problems and their solutions. Overview This chapter covers some common problems that may be encountered while using ADE-3100 and some possible solutions to them. If you follow the suggested steps and ADE-3100 still does not function properly, contact your dealer for further advice. General Problems Question 1: Can't connect to ADE-3100 to configure it. Page 54 Appendix A - Troubleshooting I reconnect it. Answer 2 You have to go to the PPP link under Status column, choose the correct PVC and Connect option, and then click Execute to restart a new PPP secession. Question 3 Since only one PVC is mapped to one local PC IP address, why can I input more than one IP address for one NAT session. Answer 3 Even it is applicable to insert multiple IPs for NAT mapping, only the first IP address of each session takes effect. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Planet Technology ADE-3100. To start viewing the user manual Planet Technology ADE-3100 on full screen, use the button Fullscreen. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Planet Technology ADE-3100 but the selected pages only. paper. If you want to quickly view the content of pages found on the following pages of the manual, you can use them. You'll find such information in the Manual of your Planet ADE-3100 router.

But if you do not have the manual for your router or you do not want to read the whole manual to find the default login information then you can use the quick guide below. To get to the router login page it's necessary that you are connected to the router. After some seconds our tool will show a link to your router login page. Click on the shown link. The default password is epicrouter. Sometimes the username and password doesn't work that we mentioned in the top of this guide.Did you try the following IPs? In the list below we listed all known router IPs for the manufacturer Planet. Maybe this will work for you.This can be done easily by clicking on the reset button at the back or at the bottom of your router. If you hold down this small button for approximately 20 seconds, (you may have to use a toothpick), then your modem will get restored to the factory settings. What you need to keep in mind is that when you reset your modem, you will lose your connection online. It is therefore better to take an expert's assistance in this regard. Please check your inbox, and if you can’t find it, check your spam folder to make sure it didn't end up there. Please also check your spam folder. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET. Should the programs prove defective following their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, PLANET reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

This network management system is intended to perform an overall monitoring and configuring features for the PLANET Mesh Network. The following are the recommended system requirement. Once completed, a menu screen will appear. Click the “PLANET Mesh Network Manager” hyperlink and select “Open” or “Run” to initiate the install wizard. Press Next to proceed. Press Next to proceed. Press Next to proceed. Press Install button to start the installation. Once the installation is completed it will direct the user to the next step. Press Done to conclude the installation. After that, you may launch the NMS through the shortcut you created previously. Launch the uninstaller wizard by double-click the executable file. Follows the following steps: Click Uninstall to start the process. Once the progress is completed, it will automatically direct you to the next step. You may choose to restart the terminal instantly or afterward in order to complete the process. Then, launch the NMS at the location where you install it. A dialog box would appear, select SNMP Map and enter the name of the new profile. After that, hit the OK button to complete the set up. A new map will be inserted into the NMS. Enter the desired IP and click the button next to the list to save the IP. Finally, select the Start Scan button on the map’s toolbar, the scan will be initiated and run. The result of the scan will be plotted on the map area. User is free to adjust the position of the found-unit on the map. A dialog box would appear, select Layer-2 Map and enter the name of the new profile. After that, hit the OK button to complete the setup. A new map will be inserted into the NMS. The saved profile can be loaded directly to the NMS next time using the Open Map button on the toolbar. The network will be displayed in the form of graphical topology map, and the status will be updated periodically. More than one map can be created and run simultaneously.

The status of the map will be logged to the status pane at the bottom of the map. Each topology map has its own status pane. It is used to display the properties of the selected Mesh AP unit on the topology map. The information of the AP will be loaded into the table, and the graph below the table shows the signal strength between the selected AP with its neighbour APs. The column at the bottom of this panel is used to invoke the live stat monitoring feature. The panel is divided into two parts, the Client Properties and Client Signal Strength portion. Each portion will be automatically updated every minute, to provide the admin user With the correct community and password, user can perform the SNMP actions such as SNMPGet, SNMPSet and SNMPTable. User can load and unload MIB file from the desired location. More than one file can be loaded into the MIB Reader. In order to read or set an item, expand the MIB tree, select the desired node. Select the SNMP version; fill in the IP Address and other necessary keyword. Then click on the command button ( SnmpGet, SnmpSet, SnmpWalk, Load Table, etc.) on the toolbar. The output will be shown on the Output column. It received the SNMP alarms and notifications directed by the Mesh AP units and display in the table at the center frame. Select the table entry in order to view the description of the trap. These alarms should be deleted once they were reviewed and resolved, by clicking the Delete button. These two types of map look similar. The main difference between them is the method to get the topology information. Prior to this, user is required to add the information of the NMS terminal (IP Address) to the node. Thus in fact, the Layer-2 Map can receive the notification not only from the layer-2 mode AP, but any other mode as well, as long as the NMS Address table is set. A window would turn out to prompt user for the type and name of the new map.