adec cart manual

In the case of a defective warranty item, a copy of the replacement invoice, serial number of the unit under which it was replaced, and a description of the symptoms of the defect must be returned with the part to: A-dec Inc. 261 Crestview Drive, Newberg, Oregon 97132, USA. 5 Equipment Alterations Policy: Certain modifications or alterations of A-dec equipment which expand the use of A-dec equipment beyond its design and intent, or which override any safety features of A-dec equipment may jeopardize doctor, patient or staff safety. Examples of field modifications that diminish safety design include, but are not limited to, rendering access to the line voltage without the use of tools, modification of supporting elements that increase or shift loading characteristics, and the addition of any powered device that exceeds the design limits of the dental system. The use of accessory equipment not complying with the equivalent safety requirements of A-dec equipment may lead to a reduced level of safety of the resulting system. It is the responsibility of the equipment distributor and the installer to assure that the installation complies with all building code requirements. A-dec will not respond to inquiries on an individual basis. This person(s) will be deemed to have assumed all associated risks with such alteration or modification and will hold A-dec harmless from resulting claims, including product liability claims. Additionally, such modification or alteration voids A-dec's warranty and may invalidate UL or other regulatory agency approval. All product names used in this document are trademarks or registered trademarks of their respective holders. This system provides automatic control of each handpiece. Until you lift a handpiece from its holder, it is inactive and cannot operate. As soon as you lift a handpiece it automatically becomes active, allowing it to run when you press the foot control disc.

• adec dental cart manual, adec 2562 dental cart manual, adec dental cart service manual, adec cart manual, adec cart manual download, adec cart manual pdf, adec cart manual online, adec cart manual instructions, adec 2562 dental cart manual, adec dental cart service manual, adec cart manual, adec cart manual download, adec cart manual pdf, adec cart manual online, adec cart manual instructions, adec dental cart manual.

I've got a problem where one of the handpieces is always switching on, even when in the holder, and could do with a few diagrams to see what could be the problem. Thanks for any help. A-dec's sole obligation under the warranty is to provide parts for the repair, or at its option, to provide the replacement product (excluding labor). The buyer shall have no other remedy. All special, incidental, and coincidental damages are excluded. Written notice of breach of warranty must be given to A-dec within the warranty period. The warranty does not cover damage resulting from improper installation or maintenance, accident or misuse. The warranty does not cover damage resulting from the use of cleaning, disinfecting or sterilization chemicals and processes. The warranty also does not cover light bulbs. Failure to follow instructions provided in the A-dec owner's guide (operation and maintenance instructions) may void the warranty. A-dec warrants A-dec dental chair cylinders, both lift and tilt, for ten years from the date of purchase of the chair or the cylinder. This warranty is retroactive to A-dec chair cylinders already in the field. The warranty covers chair cylinders A-dec finds to have manufacturing related irregularities. Stool cylinders are covered under A-dec's one-year warranty. NO OTHER WARRANTIES AS TO MERCHANTABILITY OR OTHERWISE ARE MADE. 4 Return Policy: U.S. and Canadian dealers wishing to return overstock (unopened) merchandise to A-dec for credit consideration must include a copy of the original invoice number. A 15% restocking fee will be assessed. Merchandise that cannot be returned for credit includes parts assembled to the dental unit, chair, light, or dental furniture; obsolete parts; and specials. Dental furniture cannot be returned for credit. Standard color upholstery ordered for obsolete chairs or stools cannot be returned for credit.

Turn counterclockwise to increase the flow. 7. The coolant air has been set for ALL handpieces. Turn the control clockwise to decrease the flow. Turn counterclockwise to increase the flow. 7. Adjust the coolant water for EACH handpiece. WATER COOLANT ADJUSTMENT KEY MASTER 1 Figure 8. Coolant Water Adjustment 8 15 The handpiece tubing flush system flushes more water through the tubings in less time than is normally possible when operating the foot control only. The handpieces should not be connected when flushing the tubings. How Often Should Handpiece Tubing be Flushed. After Each Patient: Flush the tubings for about 2-3 seconds. At the Beginning of Each Day: Flush the tubings for 2-3 minutes. Flushing the Handpiece Tubings Gather up all the handpiece tubings that use coolant water and hold them over a sink, cuspidor bowl or basin. Be sure you hold the tubings so that the water will be directed away from you and into the receptacle (see Figure 9). Locate the handpiece tubing flush toggle (see Figure 9). Move the toggle toward the front of the cart and hold for the appropriate time required, either for flushing between patients or flushing at the beginning of each day. Release the toggle and replace the tubings in their holders. However; if a holder is difficult to reposition or repositions too easily, the holder tension can be adjusted. To adjust the holder tension: Loosening or tightening the tension adjustment screw shown in Figures 1. To reposition a holder: Rotate the holder to the desired angle. Figure 1. Individual Handpiece Holder 1 17 Handpiece Dry Block Conversion Your Cascade handpiece control system has one to four handpiece control blocks with coolant water to the handpiece. In some cases a control block without coolant water, a dry block, is required. If you require a dry block (offering no water to the handpiece) on your handpiece control system, a dry block conversion kit has been included with your system.

With the exception of the drive air pressure gauge, all controls and indicators are located on the sides and bottom panel of the unit. Autoclavable adjustment keys (see Figure 1) are provided for making adjustments to the recessed controls. You may also order additional keys from your authorized A- dec dealer. Turns on and off the air, water, and electrical power to the system. This will prevent the possibility of water damage should a leak occur while the unit is unattended. MASTER 1 DRIVE AIR PRESSURE GAUGE Figure 3. Drive Air Pressure Gauge Water Outlet with Flow Control The water outlet with flow control (see Figure 4) provides water for hydrocolloid tubing. The outlet accepts A-dec s quick disconnect (QD) flow-control. Flow is controlled by a knob on the QD itself. To increase flow, turn the knob counterclockwise; to decrease flow turn the knob clockwise. KNOB WATER OUTLET QUICK DISCONNECT (QD) FLOW-CONTROL QUICK DISCONNECT (QD) Figure 4. Water Outlet With Flow Control 4 11 The foot control modulates drive air to the active handpiece and provides an air signal that activates the coolant air and coolant water flow. The foot control is operated by light foot pressure applied to any part of the foot control disc. Allows you to shut off the coolant water to the handpiece without moving your hands from the oral cavity. Using your foot, move the toggle away from the blue dot to turn the coolant water OFF. Move the toggle toward the blue dot to turn the coolant water ON. Adjust the drive air pressure to meet the handpiece manufacturer s dynamic drive air pressure specification. Refer to the documentation that came with your handpiece for the dynamic drive air pressure specification. Turn the drive air control counterclockwise to increase drive air pressure flow. Turn the control clockwise to decrease flow. 7. Repeat steps 1 through 6 for EACH handpiece. A strong flow of air is recommended. Turn the control clockwise to decrease the flow.

Solids Collector The solids collector, located inside the cart (see Figure 16), collects solids and prevents them from entering the central vacuum system. To remove the canister lid, turn off the vacuum, then twist the lid counterclockwise and lift it off. At least once per week, remove and clean the solids collector screen (see Figure 17). This is necessary to ensure proper suction from the central vacuum. Refer to your Assistant s Instrumentation Owner s Guide (A-dec Publication No ) for complete solids collector maintenance instructions. LID SCREEN CANISTER Figure 17. Pre-Regulator controls the air and water pressures in the unit. The procedure for adjusting system pressure is given on page 17. Air and Water Filters prevent solids from entering the unit. In-Cart Utilities 16 23 System Air and Water Pressure Adjustments The air and water manual shutoff valves, as well as any vacuum or drain outlets, are located in the floor box mounted over the office plumbing on the floor or wall. Before making any adjustments to components in the cart top, verify that the manual shutoff valves in the floor box are all the way open (turned fully counterclockwise) and that the compressor is on and functioning properly. The air compressor should maintain 8 12 psi ( kpa) in the tank. Air pressure should be 7 8 psi ( kpa). Water pressure should be 35 4 psi ( kpa). 4. While watching the gauges, operate the syringe. If the system air pressure drops by more than 15 psi (13 kpa), or water pressure by more than 1 psi (69 kpa), check for clogged filters. 17 24 System Air and Water Pressure Adjustments (continued) 5. If adjustment of either the air or water pressure is required, turn the appropriate pre-regulator knob (see Figure 19). Clockwise to increase pressure. Counterclockwise to decrease. Make sure air and water pressure are maintained.

Bleed the system water by operating the syringe and flushing the handpiece tubings. 2. Locate the handpiece control block position that will be the dry block. Install the small black cartridge from the dry block conversion kit into the control block (see Figure 11). 5. Turn your handpiece control system on, then check the function of the dry block handpiece conversion. A small amount of residual water may be discharged from the handpiece tubing but should dry after a few seconds. DO NOT REMOVE THE YELLOW CARTRIDGE REMOVE THE BLUE CARTRIDGE AND REPLACE WITH THE SMALL BLACK CARTRIDGE REMOVE THE RED CARTRIDGE AND REPLACE WITH THE LARGE BLACK CARTRIDGE Figure 11. Handpiece Dry Block Conversion 11 18 Oil Collector The oil collector on your unit needs to be changed once a week for normal usage. Change more often for heavier use. 1. Remove the oil collector jar from the unit and discard the old gauze (see Figure 12). 2. Fold in quarters a new two inch square gauze pad and place against the spring inside the jar. 3. Screw the oil collector jar onto the unit. Do not overtighten. CART HOUSING Figure 12. Oil Collector Care Instructions For recommended asepsis instructions, refer to your Equipment Asepsis Owner s Guide (A-dec Publication No ). Air Press the right button down. Water Press the left button down. AIR WATER SPRAY Figure 13. Autoclavable Syringe Spray Press both buttons down. Syringe Flow Controls. Located underneath the cart top. The autoclavable HVE and saliva ejector can be easily converted for right- or left-hand operation. To convert, press the control valve out of the valve body (see Figure 15). Rotate the control valve 18, then press it back into the valve body. Refer to your Assistant s Instrumentation Owner's Guide (A-dec Publication No ) for complete instructions on cleaning your HVE and saliva ejector. VALVE BODY VALVE BODY CONTROL VALVE AUTOCLAVABLE SALIVA EJECTOR CONTROL VALVE AUTOCLAVABLE HVE Figure 15.

Two bezels Tie brackets used to secure multiple Your system includes the following items: 1 Fascination 700 HVLP Tanning Pro Page 2 2 Installation. Page 10 5 Troubleshooting Page Missing Parts? 4 Installation (Wall mount) 6-9 Installation (Eave mount) To use this website, you must agree to our Privacy Policy, including cookie policy. You can now find it at www.dciedge.com. Creating an online account will give you access to view pricing for all products, participate in the support forum, and more. I am not a DCI customer and want to become one. You will be able to view your pricing for all products, participate in the support forum and more. You must be a DCI customer to register. Are you interested in becoming a DCI customer.Send us your question and we'll get back to you within one business day. If after hours, your question will be answered the next business day. Contact us and let us help. It has known security flaws and may not display all features of this and other websites. Please upgrade to one of these free browsers. You will be notified by e-mail once your account has been activated by the store owner. If you have ANY questions about the operation of this online shop, please contact the store owner. It is now safe to leave the computer. Your shopping cart has been saved, the items inside it will be restored whenever you log back into your account. They are both Light Grey and one has Ingot Trim w. It has been completely stripped, re-tubed, painted, new diaphragms, and new regulators. Features I. Hayam Wuruk, Tamansari Jakarta Barat, Jakarta 11180 Indonesia Endoscopy: Bronchoscopes, Colonoscopes, Duodenoscopes, Gastroscopes. Watch our COVID-19 response. Creating an online account will give you access to view pricing for all products, participate in the support forum, and more. I am not a DCI customer and want to become one. You will be able to view your pricing for all products, participate in the support forum and more.

You must be a DCI customer to register. Are you interested in becoming a DCI customer.Send us your question and we'll get back to you within one business day. If after hours, your question will be answered the next business day. Contact us and let us help. Find a dealer near you. It has known security flaws and may not display all features of this and other websites. Please upgrade to one of these free browsers.

NOTE When decreasing system air or water pressure, you will not see the air or water pressure gauge in the utility center change until you relieve pressure from the system. Activate the syringe for a few seconds, then check the gauge. Repeat this process each time you make an adjustment to decrease pressure. 18 25 Filter Maintenance Air and Water Filter Elements Air and water pass through separate filters in the utility module before entering the regulator. A filter must be replaced when it becomes sufficiently clogged, restricting flow to the regulator. To determine the location of your system utility module, (see Figure 18 on page 16). While watching the air pressure gauge in the cart top, press the syringe air button. If the air pressure indicated by the gauge drops by more than 15 psi (13 KPA), the filter element is clogged and must be replaced. While watching the water pressure gauge in the cart top, press the syringe water button. Bleed the system of air and water pressure by operating the syringe buttons until air and water no longer flow. Using a standard (flat-blade) screwdriver, remove the filter housing from the utility module (see Figure 2) and remove the filter. FILTER HOUSING BEVELED EDGE AIR SIDE (White Regulator) O-RING (Part No ) FILTER ELEMENT (Part No; Pkg of 6: ) WATER SIDE (Black Regulator) Figure 2. Filter Replacement UTILITY MODULE If the filter is visibly clogged or discolored, you will need to replace it. Order A-dec Part No When installing a new filter, notice that one end of the filter has a beveled edge. Install the filter with the beveled edge facing the utility module (see Figure 2). Weights of optional attachments: Tooth Dryer: 1 lb (.45 kg) Intra-Oral Light Sources: 1 lb (.45 kg) Duplex Receptacle Ratings: 12 VAC, 2A maximum, branch circuit breaker limited. Conforms to applicable European Directives (refer to Declaration of Conformity). Protective earth (ground). Functional earth (ground). Attention, consult accompanying documents.

No user servicable parts. Attention, line voltage. Only licensed electrician should remove cover. Type B applied part. Class II equipment. Caution: Metal surfaces can be hot during and following the dry cycle.A-dec 500 Assistant s Instrumentation. Model 551 All rights reserved. A-dec Inc. The instructions contained in this booklet should be thoroughly read and understood User Manual For Models: DH45S DH65S Users Manual This manual is the best copy we could find; it may be incomplete or contain dated information. Before completing installation, The operator must carefully read and follow Failure to do so can result in serious Class B devices have a Federal Communications AeroVironment, EV Solutions, and the AeroVironment logo are trademarks Safety Warning: Indirect water heaters are heat-producing You can find these numbers printed on the bottom of the table.When tipping the Cable Processor Module back, (after removing the toggle arm pin), use extreme caution not to drop Preparation. Tools Needed. Wiring. Hanging the Fan. Blades. Motor Housing. We work around the clock and around the globe to ensure that our products maintain Your failure Serial Number: Model - OCSM Congratulations! Contents Congratulations on your purchase of a Next Advance Pressure Injection Cell. Please read this operator s manual which explains proper Automatic Dispensing Hot Water Pot with Reboil Function Since 1969 our goal has been to design, test, and produce solar heating systems that save you CAUTIONS Solar electric modules produce DC electricity Installation and Operation Manual For use with STATIM 2000 and STATIM 5000 Autoclaves. Installation Guide and Operator s Manual Instruction Manual Young children should be supervised to CFS01 Series, CFS02 Series, CFS11 Series, and CFS12 Series Housings. Installation and Instruction Manual For: Notify the carrier and dealer if there is damage.